It seems like such a huge amount of water and would require so much energy to get it that high, plus there’s the waste to deal with

  • Tolookah@discuss.tchncs.de
    link
    fedilink
    English
    arrow-up
    58
    arrow-down
    1
    ·
    5 months ago

    Waste is easy, it goes down.

    For pressure, high rises have a pump in their machine room that pumps water upwards. It used to be water towers on the roofs of buildings that aides pressure

    • whyrat@lemmy.world
      link
      fedilink
      English
      arrow-up
      60
      ·
      5 months ago

      A bit of an elaboration on why water towers are used in combination with pumps. Pumps are great for moving a constant amount of water around at whatever rate the pump is designed for (e.g. a small pump will move something like 1 gallon per minute). a big enough pump (or series of smaller pumps) can cause that pumped water to consistently flow at that rate.

      The problem is that people don’t use water at a constant rate. In the morning, several residents probably all run the shower at the same time. if too many people open the water tap at the same time, a pump will give each just a fraction of what they expect.

      But a water tank high up supplies water by gravity, you could open a large number of water taps, and as long as the pipes from the tank are big enough they’d all have the same pressure as if just one opened.

      The water is gradually pumped up to the tank no matter if people are using it or not, then when many people want water, they all get it at expected pressures and the tank start to empty. Eventually people close the taps, the tank will slowly start to fill again from the pump.

      This same basic design is also how water towers supply water to many single story buildings, it’s not a unique engineering feat for skyscrapers, but an adjustment to fit somewhere within the building’s footprint.

    • KillerTofu@lemmy.world
      link
      fedilink
      English
      arrow-up
      28
      arrow-down
      1
      ·
      5 months ago

      And water towers are still used to manage water pressure demands in municipalities.

      • gravitas_deficiency@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        23
        ·
        5 months ago

        Yeah - if you’re in NYC at any point and go up anywhere you can see roofs of a lot of buildings, you’ll see a TON of water tanks and towers on older stuff.

    • datavoid@lemmy.ml
      link
      fedilink
      English
      arrow-up
      16
      ·
      5 months ago

      Back when I lived around the 30th floor, I would turn on the tap and then wait 10 minutes for the hot water to arrive.

      The trick was to wait until the people above you were having a shower, then it would already be hot.

  • jqubed@lemmy.world
    link
    fedilink
    English
    arrow-up
    45
    ·
    5 months ago

    I’m no expert, but I’ve looked at this in the past. Most large buildings have their own water tanks inside them. If you think of an image of a New York skyline away from the skyscrapers you might picture small water towers on top of most of the buildings. Those are the tanks that supply water for the building. Skyscrapers will have multiple tanks inside the building itself, maybe one every 5 or 10 floors up. There will always be one at the top of the building but it might not be as obvious looking as a small water tower. Each tank will serve just the floors in between it and the next tank below. When the tank needs to be refilled it just draws from the tank below it. This way the building doesn’t pump all the water it needs all the way to the top floor; it only pumps water as high as it needs to go. Keeping water in a tank means it still works like a traditional gravity-fed system and should function for a while even in the event of a power outage.

    Handling wastewater is relatively easier, it still just needs to flow down. The pipes just drain into one or more pipes going down to the bottom of the building.

      • Captain Aggravated@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        13
        ·
        5 months ago

        Yes.

        Take New York for example. It is my understanding that New York’s municipal water system has enough pressure to pump water 5 stories high, so many of the relatively smaller buildings have large wooden water tanks on their roofs to keep that building’s water pressure relatively constant even during peak demand times. Larger buildings are responsible for pumping their own water hundreds of feet into the air.

      • jqubed@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        5 months ago

        Yes, but multiple tanks throughout the building means they don’t have to pump all the water all the way to the top. They only need to pump the water for the highest floors to the top.

  • Thorny_Insight@lemm.ee
    link
    fedilink
    English
    arrow-up
    25
    ·
    5 months ago

    Plumber here. Unless we’re talking about sky scrapers the grid pressure is generally enough to lift the water to the top floors. As long as it’s lower than the city water tower there’s no issue. If it’s a flat terrain or the building is on a hill then yes, you might need a pump to boost the pressure. Sewage on the other hand is not an issue - gravity takes care of that.

  • 5714@lemmy.dbzer0.com
    link
    fedilink
    English
    arrow-up
    21
    ·
    5 months ago

    How Water Towers Work | https://www.youtube.com/watch?v=yZwfcMSDBHs | by Practical Engineering

    High buildings sometimes have their higher floors above the height level that the water pressure from the water supply of a town can reach.

    Those buildings then use pumps in the cellar to either pump the water to a tank on the highest floor and let it fall down again to the floors or to pump the water to the floors directly.

  • ChaoticNeutralCzech@feddit.org
    link
    fedilink
    English
    arrow-up
    6
    ·
    5 months ago

    Toilet waste (black) water pipes are quite underused for their diameter so it’s enough to just feed dozens of bathrooms’ worth into a reasonable diameter you can still get at a hardware store. Sure, some will have trouble flushing if they all do that at the same time but not too serious.

    As for drinking water, some high-rises feature tanks as part of their oscillation damping system anyway, and municipal water towers don’t need to be placed much higher than customers to get decent pressure. I think it’s not the amount but pressure of water at the ground floor that causes engineering challenges. The pumps and tank at the top help, though.